欢迎访问青州久泰包装设备有限公司!

My title

2头半自动活塞式油类灌装机

名称:2头半自动活塞式油类灌装机
详细信息 :

1、活塞式灌装机是一种对高浓度流体进行灌装的灌装机,它是通过气缸带动一个活塞及转阀的三通原理来抽取和打出高浓度物料,并以磁簧开关控制气缸的行程,即可调节灌装量。

2、本设备具有设计紧凑美观、操作简单易懂、 度高等特点。

3、本机采用特殊三通灌装阀,通过气缸的往复运动实现物料的灌装,是理想的手工作业的替代设备。

4、物料接触部分均采用304L不锈钢材料制成,符合GMP要求。对于强腐蚀性液体,物料接触部分采用聚四氟乙烯材料,以确保设备的长期稳定运行。

5、灌装量和灌装速度均可任意调节,灌装精度高。

6、灌装闷头采用防滴漏、防拉丝及升降灌装装置。

7、适用于:食品、医药、日化、农药等行业

安装及调试

1、该机开箱后按说明书安装,并接通压缩空气气源,气源压力0.6MPa如在压缩空气主管道接应先装阀门。

2、打开右门旋出油雾器油标加入清洁的专用机油,或缝纫机油,注意:加油时不能带气压,油量约加至8分满为宜。

3、通入气源检查各密封面是否漏气,调节气压为0.3~0.4MPa调节进油量,一般动作若干次后喷一滴油即可,定期检查喷油情况。

4、灌装量调节:先旋转灌装量调节手轮,观察指示窗刻度,使达到所需要的装量,同时调节吸料、出料速度以达到满意的灌装效果,用量标测灌装量, 后修正灌装量。 清洗要求

操作前要清洗,用无纺软布加清洗剂擦去油污或污垢,然后用无纺软布擦干。按照GMP要求,检查设备与物料接触部位是否符合相应洁净要求.

操作及维护

1、当发现灌装时计量不稳定时,应检查进料单向阀可能有杂物夹住,导致密封不严,影响灌装量。

2、缸体下部漏料,说明活塞密封圈磨损,需要更换密封圈。

适用范围

适用于日化、医药、食品、农药等各个行业。

1.a piston type filling machine is a filling machine filling of high concentrations of fluid, it is through the cylinder drives a piston and rotary valve three-way principle to extract and hit the high concentration material, and the magnetic reed switch control cylinder stroke, you can adjust the filling volume.

2.the device has a compact design, easy to understand, high degree of.

3.the machine uses a special three - way filling valve, through the reciprocating motion of the cylinder to achieve the filling material, is an ideal manual operation of the replacement equipment.

4.material contact parts are made of 304L stainless steel materials, in accordance with the requirements of GMP. For the strong corrosive liquid, material contact part of the use of PTFE materials, to ensure the long-term stable operation of the equipment.

5.filling volume and filling speed can be arbitrarily adjusted, high filling accuracy.

6.filling head adopts anti drip, drawing and filling lifting device.

7.applicable to: food, medicine, daily chemicals, pesticides and other industries

Installation and commissioning

1.the machine out of the box according to the instructions to install and connect the compressed air supply, air pressure is 0.6MPa as in compressed air main pipe slips to install the valve.

2.open the right door spin out of standard oil mist, oil adding special cleaning oil or sewing machine oil. Note: the refueling can not bring pressure, oil volume reduction to 8 minutes full advisable.

3.through the gas source to check the sealing surface is flat, adjust the pressure to adjust the amount of oil into the 0.3~0.4MPa, the general action of a number of times after the injection of a drop of oil can be regularly check the fuel injection.

4.adjustment of filling volume: first rotating filling quantity adjusting hand wheel was observed, indicating dial window, so as to meet the need of the loading quantity, and adjust the suction and discharging speed to achieve a satisfactory filling effect, dosage mapping filling volume, after correction filling volume. Cleaning requirements

Comprehensive cleaning before operation, with non-woven soft cloth cleaning agent to remove grease and dirt, and then use non-woven soft cloth. According to GMP requirements, inspection equipment and material contact parts are in line with the corresponding clean requirements.

Operation and maintenance

1.when the measurement is not stable when filling, check the feed check valve may have debris caught, resulting in tight seal, the impact of filling capacity.

2.the lower part of the cylinder leakage material, the piston seal ring wear, the need to replace the sealing ring.

Scope of application

Apply to the daily chemical, pharmaceutical, food, pesticide and other industries.